0
0
mirror of https://git.openwrt.org/openwrt/openwrt.git/ synced 2025-10-05 23:42:55 +02:00
Markus Stockhausen f88135b7cd realtek: add support for Linksys LGS352C
Hardware specification
----------------------

* RTL9311 SoC, 2 MIPS Interaptiv cores @ 1000MHz
* 512MB DRAM
* 2MB NOR Flash
* 128MB NAND Flash
* 48 x 10/100/1000BASE-T ports
* 4 x 10G SFP+ ports
* LM63 controlled fan
* Power LED, Fault LED
* Reset button on front panel
* UART (115200 8N1) via RJ45

Installation using serial interface
-----------------------------------

1. Press "a" "c" "p" during message "Enter correct key to stop autoboot"
2. Start network "rtk network on"
3. Load image "tftpboot <TFTP IP>:openwrt-realtek-rtl931x_nand-linksys_lgs352c-initramfs-kernel.bin"
4. Boot image "bootm"
5. Switch to first bootpartition "fw_setsys bootpartition 0"
5. Download sysupgrade "scp <IP>:openwrt-realtek-rtl931x_nand-linksys_lgs352c-squashfs-sysupgrade.bin /tmp/."
6. Install sysupgrade "sysupgrade /tmp/openwrt-realtek-rtl931x_nand-linksys_lgs352c-squashfs-sysupgrade.bin"

Installation using OEM webinterface
-----------------------------------

This is not possible because the OpenWrt NAND Flash layout is different
from the vendor layout. To be precise. Vendor uses:

- 64 MB vendor UBI root_data
- 32 MB vendor kernel+root 1 (~19 MB used)
- 32 MB vendor kernel+root 2 (~19 MB used)

OpenWrt uses:

- 64 MB vendor UBI (not touched)
- 10 MB OpenWrt kernel
- 22 MB Openwrt mtd-concat UBI
- 23 MB vendor kernel 2 (space reduced, vendor data unchanged)
- 09 MB OpenWrt mtd-concat UBI

Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------

From stock to OpenWrt / primary image 1 (CLI as admin):
   - > boot system image1
   - > reboot

From OpenWrt to stock / boot image 2: (shell as root)
   - # fw_setsys bootpartition 1
   - # reboot

Debrick using serial interface
------------------------------

1. Press "a" "c" "p" during message "Enter correct key to stop autoboot"
2. Load vendor image with "upgrade runtime <TFTP IP>:LGS352xxxxx.imag"
3. switch to primary partition "setsys bootpartition 0"
4. safe config "savesys"

Further documentation
---------------------
See https://openwrt.org/toh/linksys/lgs352c

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20255
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-10-05 12:14:05 +02:00
2025-09-12 21:04:15 +02:00
2025-10-04 20:34:38 +02:00
2024-05-17 22:03:06 +03:00
2021-02-05 14:54:47 +01:00

OpenWrt logo

OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.

Sunshine!

Download

Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.

If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.

An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:

Development

To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.

Requirements

You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.

binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which

Quickstart

  1. Run ./scripts/feeds update -a to obtain all the latest package definitions defined in feeds.conf / feeds.conf.default

  2. Run ./scripts/feeds install -a to install symlinks for all obtained packages into package/feeds/

  3. Run make menuconfig to select your preferred configuration for the toolchain, target system & firmware packages.

  4. Run make to build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.

The main repository uses multiple sub-repositories to manage packages of different categories. All packages are installed via the OpenWrt package manager called opkg. If you're looking to develop the web interface or port packages to OpenWrt, please find the fitting repository below.

  • LuCI Web Interface: Modern and modular interface to control the device via a web browser.

  • OpenWrt Packages: Community repository of ported packages.

  • OpenWrt Routing: Packages specifically focused on (mesh) routing.

  • OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).

Support Information

For a list of supported devices see the OpenWrt Hardware Database

Documentation

Support Community

  • Forum: For usage, projects, discussions and hardware advise.
  • Support Chat: Channel #openwrt on oftc.net.

Developer Community

License

OpenWrt is licensed under GPL-2.0

Description
No description provided
Readme 253 MiB
Languages
C 59.6%
Makefile 19%
Roff 8.9%
Shell 6.8%
Perl 2.6%
Other 3%