272fc1348ea9 lua: CMakeLists: drop redundant cmake_minimum_required
5e69edac2ec4 CMakeLists: fix CMake warning for INCLUDE macro
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The first RTL931x devices make their way into OpenWrt. Their copper
ports are driven by different interfaces modes like 10G_QXGMII or
Realtek proprietary XSGMII. The DSA driver has no proper handling
for theses modes implemented yet. So a lot is auto-mapped to USXGMII
internally. As soon as the SerDes setup activates this (wrong) mode
the PHY connectivity breaks.
Disable this mode for now and rely on the proper U-Boot setup.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20292
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Realtek NAND kernel configuration has some shortcomings.
Fix this as follows:
- MTD_NAND_ECC_REALTEK selects MTD_NAND_ECC and this selects
MTD_NAND_CORE. For consistency add both config options.
- The partition layout of the Linksys switches requires some tricky
concatenation to keep dual boot active. Add CONFIG_MTD_VIRT_CONCAT
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20255
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interface might be down or scanning. Better do a full restart in order to avoid
messing up the runtime state.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Plasma Cloud PAX1800-Lite is a dual-band Wi-Fi 6 router, based on MediaTek
MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621AT (880 MHz)
- DRAM: DDR3 448 MiB (Nanya NT5CC256M16DP-DI)
- Flash: 2 MiB SPI NOR (S25FL016K) + 128 MB SPI NAND (W25N02KVZEIR)
- Ethernet: 1x 10/100/1000 Mbps (SOC's built-in switch, with PoE+)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: tri-color LED for status (red, blue, green)
- Buttons: 1x (reset)
- Antenna: 4x internal, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, marked as "3V3 G/RX GND W/TX")
- Power: 12 V DC/2 A (DC jack)
MAC addresses:
WAN: 54:9C:27:xx:xx:00 (factory 0x3fff4, device label)
2.4 GHz: 54:9C:27:xx:xx:02 (factory 0x4, device label +2)
5 GHz: 54:9C:27:xx:xx:08 (factory 0xa, device label +8)
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console (115200 8N1) must be used to access the u-boot shell
during bootup. It can then be used to first boot up the initramfs image
from a TFTP server (here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0x83001000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mt76 as support for generic rates power limits in the devicetree. But the
mt7915 supports beamforming and has another table for configuring the
backoff limits. These can be configured in the DT with the paths-*
properties. The path-*-bf are the ones relevant for beamforming and the
ones without -bf suffix for "traditional" path backoff.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The power-limits for ru and mcs and stored in the devicetree as bytewise
array (often with sizes which are not a multiple of 4). These arrays have a
prefix which defines for how many modes a line is applied. This prefix is
also only a byte - but the code still tried to fix the endianness of this
byte with a be32 operation. As result, loading was mostly failing or was
sending completely unexpected values to the firmware.
Since the other rates are also stored in the devicetree as bytewise arrays,
just drop the u32 access + be32_to_cpu conversion and directly access them
as bytes arrays.
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to the MT7628 hardware datasheet:
- GPIO/4 was originally used for I2C, but is now used as the Modem Power.
- GPIO/5 was originally used for I2C, but is now used as the SIM card select. (n/a for this device)
- GPIO/6 was originally used for SPI CS1, but is now used as the Serial mode switch.
- GPIO/36 was originally used for PERST, but is now used as the GPS OE. (n/a for this device)
- GPIO/38 was originally used for WDT, but is now used as the Modem2 Power. (n/a for this device)
- GPIO/44 was used for WLED_AN, but is now controlled by `gpio-leds`.
Corrected pinctrl to ensure it works properly in the future.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20256
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
release is Moderate.
This release incorporates the following bug fixes and mitigations:
Fix Out-of-bounds read & write in RFC 3211 KEK Unwrap.
(CVE-2025-9230)
Fix Timing side-channel in SM2 algorithm on 64 bit ARM.
(CVE-2025-9231)
Fix Out-of-bounds read in HTTP client no_proxy handling.
(CVE-2025-9232)
Reverted the synthesised OPENSSL_VERSION_NUMBER change for the release
builds, as it broke some exiting applications that relied on the previous
3.x semantics, as documented in OpenSSL_version(3).
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Plasma Cloud ESX28 Switch is a 24 + 4 port multi-GBit switch with
24x 10/100/1000/2500BaseT Ethernet ports and 4x SFP+ module slot.
Hardware:
- RTL9312C SoC
- Macronix MX25L25645G (32MB flash)
- 512MB DDR3 SDRAM
- RTL8231 GPIO extender to control the port LEDs
- 6x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 4x 10GBit slot
The switch is powered directly via AC.
The external RS232 serial connector (RJ45, Cisco pinout) can be used to
access the terminal. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial on front panel. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl931x-plasmacloud_esx28-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl931x-plasmacloud_esx28-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x5e0000 0x1a20000
# write firmware to both partitions
sf write ${fileaddr} 0x5e0000 ${filesize}
sf write ${fileaddr} 0x12f0000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:768k(u-boot),64k(u-boot-env),64k(u-boot-env2),5120k(reserved),13376k(inactive),13376k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb52f0000"
# restart
reset
Debug
-----
* Connect serial on front panel. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enter passwords: "1234" or "plasmapsx"
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl931x-plasmacloud_esx28-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Plasma Cloud PSX28 Switch is a 24 + 4 port multi-GBit switch with
24x 10/100/1000/2500BaseT Ethernet ports and 4x SFP+ module slot.
Hardware:
- RTL9312C SoC
- Macronix MX25L25645G (32MB flash)
- 512MB DDR3 SDRAM
- RTL8231 GPIO extender to control the port LEDs
- 6x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 4x 10GBit slot
- RTL8239 POE++ PSE controller with frontend MCU
The switch is powered directly via AC.
The external RS232 serial connector (RJ45, Cisco pinout) can be used to
access the terminal. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial on front panel. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl931x-plasmacloud_psx28-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl931x-plasmacloud_psx28-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x5e0000 0x1a20000
# write firmware to both partitions
sf write ${fileaddr} 0x5e0000 ${filesize}
sf write ${fileaddr} 0x12f0000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:768k(u-boot),64k(u-boot-env),64k(u-boot-env2),5120k(reserved),13376k(inactive),13376k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb52f0000"
# restart
reset
Debug
-----
* Connect serial on front panel. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enter passwords: "1234" or "plasmapsx"
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl931x-plasmacloud_psx28-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To be able to read out the ethaddr from the u-boot environment for MAC
address configuration, it is required to also enable the NVMEM layout
parsing code for the U-Boot env layout.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenWrt buildroot will compile all dtbs defined in target to
$(KDIR)/image-$(DEVICE_DTS).dtb, so make use of it to allow us
debug and use external dtbs easier without patching kernel Makefile.
This also fixes commit 5c724939c3 which forgot to update DTS_DIR
in KERNEL variable.
Fixes: 5c724939c3 ("rockchip: add DEVICE_DTS_DIR definition")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20286
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4b7638925d3e iptime-crc32: add support for ipTIME AX3000M
12c0b42231be nosimg-enc: add new tool for XikeStor SKS8300 series
2051fe5bc2a1 mktplinkfw2: Add 16MLmtk layout
5d1446bf57d6 tplink-safeloader: Add more special_id's for MR70X
075cdc0c4dd4 iptime-crc32: add support for ipTIME AX3000Q
48ababab6b08 iptime-crc32: add support for ipTIME AX3000SM
f29de74ecd7d iptime-crc32: Add device support for ipTIME AX6000M
3346d7711c9a build: add mkqdimg
950f83405a93 iptime-crc32: add support for ipTIME AX7800M-6E
0725c3d4aa1b build: require CMake >= 3.5 due to dropped legacy support
996dc482a7e8 ptgen: fix misprint and simplify calculation a bit
febfef7a09b1 ptgen: use long long instead of long for sizes
6ea8b6dd44d0 ptgen: fix protective MBR partition size
f1f98b0b8456 ptgen: do not create stub partition to fill a gap if gap caused by alignment
3f2d14829150 ptgen: allow non-default placement of gpt entry table
78d8084c7376 ptgen: allow image generation for a specified disk size
9fa340db640e ptgen: create separate images for gpt data structure
d3f8b6ed940a zynsig: add new tool for creating images for the ZyXEL GS1920 series
7e6f69b444c3 npk_pack_kernel: add tool for creating MikroTik NPK kernel packages
0782d243d23e Revert "ptgen: do not create stub partition to fill a gap if gap caused by alignment"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the environment variable `CI` is set, ccache will enable the CMake
option CCACHE_DEV_MODE by default. This leads to differing behaviour
between local and CI builds which takes quite some time to debug. 🤯
Achieve consistent behaviour between local builds and CI builds by
setting CCACHE_DEV_MODE. Set it to OFF, because CCACHE_DEV_MODE amongst
other settings like linker choice, enables -Werror, which will lead to
potential compilation failures when the host compiler is updated. Using
-Werror for host utils is not desirable, because the compiler version
used is not controlled by the OpenWrt build system and host utils should
compile successfully on an as wide range of host OSes as possible.
Reported-by: Roman Azarenko <roman.azarenko@iopsys.eu>
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20290
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
d3be5474f6e6 udebug-cli: ignore zero-length messages in logstream
c79f02d899df ucode: fix skipping lines where the timestamp cannot be parsed
5327524e7153 cmake: bump minimum required version to 3.13
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
